Field work machine > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

<h2>  with the Balanset-1A Device  </h2>
 
<h3>  Preparing the Necessary Tools  </h3>
<ul>
<li>  vibration sensors, optical speed sensor, magnetic base, software package, and included accessories.  </li>
<li>  Set up the instrument and connect it to your computer via USB. Verify that the software is correctly installed.    </li>
</ul>
 
<h3>  Sensor Installation  </h3>
<ul>
<li>  Mount the vibration transducers securely on the machine's housing where vibrations are most pronounced, typically near the bearings.    </li>
<li>  Position the laser tachometer (phase angle sensor) so that it is aimed at the rotor. Attach reflective tape to the rotor for accurate phase angle reading.    </li>
</ul>
 
<h3> Launching the Software  </h3>
<ul>
<li>  Launch the Balanset software on your computer.    </li>
<li>  Configure the software for either single-plane or two-plane balancing, based on the rotor's characteristics and the desired outcome.  </li>
</ul>
 
<h3>  Measuring Initial Vibration  </h3>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/2-Camera_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/2-Camera_01.png" alt="2-Camera_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<ul>
<li>  Run the rotor up to its operating speed.    </li>
<li>  The application will acquire data on vibration magnitude, rotational velocity, and phase angle to determine the initial imbalance state.  </li>
</ul>
 
<h3> Mounting the Test Weight  </h3>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/3-Camera-2_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/3-Camera-2_01.png" alt="3-Camera-2_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<ul>
<li>  Halt the rotation and mount a test weight at a designated position on the rotor, with the weight's value entered into the software (usually in grams).  </li>
<li>  Resume rotor operation, and the program will capture the resulting changes in vibration amplitude and phase.  </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/5-Camera_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/5-Camera_01.png" alt="5-Camera_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
 
 
<h3> Calculating the Correction Weight  </h3>
<ul>
<li>  Based on the measured data, the software automatically calculates the correction weight parameters: mass and installation angle.    </li>
<li>  These parameters are displayed on the screen as numerical data and graphs.    </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/02/Bs1ManualEngV156-May2023-10448629.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/02/Bs1ManualEngV156-May2023-10448629.png" alt="Bs1 Manual" style="width: 30%; display: block; margin-bottom: 10px;">
</a>
 
<h3> Installing the Correction Weight  </h3>
<ul>
<li>  Attach the computed compensating weight to the rotor as indicated by the software's output.  </li>
<li>  You can conduct interim measurements to confirm that the imbalance is decreasing as expected.  </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/1-Camera-2_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/1-Camera-2_01.png" alt="1-Camera-2_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
 
<h3> Verification and Balancing Completion  </h3>
<ul>
<li>  After installing the correction weight, run the rotor again and check the residual vibration level.    </li>
<li>  If the measured vibration falls within the tolerance defined by ISO 1940, the balancing process is considered successful.  </li>
<li>  If the vibration is still outside acceptable limits, reiterate the process and fine-tune the compensating weight.  </li>
</ul>
 
<h3> Generating a Documentation of the Balancing Results  </h3>
<ul>
<li>  The program stores the balancing data, allowing you to generate and print a comprehensive report including vibration measurements, corrective weight details, and its angular placement.  </li>
</ul>
 
<h3> Concluding Steps and Verification  </h3>
<ul>
<li>  Ensure all applied weights and attached sensors are firmly fixed in their designated positions.  </li>
<li>  Ensure the rotor rotates smoothly and without excessive noise.    </li>
<li>  In cases where the rotor is integrated into a more complex system, ensure the correct operation and interaction of all related components.  </li>
</ul>
 
<p>  This process allows for precise imbalance correction, reducing vibration and extending equipment life.  </p>
 
 
 
 
Instagram: https://www.instagram.com/vibromera_ou/
Youtube :  https://youtu.be/guA6XJ-ArZM?si=vmkuX7RILzKBl0zL 
Our website about  <a href="https://vibromera.eu 
"> Belt-drive balancing machine </a>
Machinio: https://www.machinio.com/listings/98380186-portable-balancer-vibration-analyzer-balanset-1a-full-kit-in-portugal
Facebook: https://www.facebook.com/marketplace/item/350151228150722
 
https://bookmarkchamp.com/story16839401/hassle-free-balancing-introducing-the-new-balanset-device