자유게시판 글답변

이름필수 비밀번호필수 이메일 홈페이지

옵션

html

제목필수

내용필수

웹에디터 시작

> 
 > 
 > <h2>  with the Balanset-1A Device  </h2> 
>  
> <h3>  Getting the Equipment Ready  </h3> 
> <ul> 
> <li>  vibration sensors, optical speed sensor, magnetic base, software package, and included accessories.  </li> 
> <li>  Establish a USB connection between the instrument and the computer, ensuring the software is set up properly.  </li> 
> </ul> 
>  
> <h3>  Setting Up the Sensors  </h3> 
> <ul> 
> <li>   Mount the vibration transducers securely on the machine's housing where vibrations are most pronounced, typically near the bearings.    </li> 
> <li>   Aim the optical rpm sensor at the rotating shaft and apply a reflective strip to the shaft for phase angle data acquisition.  </li> 
> </ul> 
>  
> <h3> Launching the Software  </h3> 
> <ul> 
> <li>   Launch the Balanset software on your computer.    </li> 
> <li>  Configure the software for either single-plane or two-plane balancing, based on the rotor's characteristics and the desired outcome.  </li> 
> </ul> 
>  
> <h3>  Initial Vibration Measurement  </h3> 
> <a href="https://vibromera.eu/wp-content/uploads/2024/11/2-Camera_01.png" target="_blank"> 
> <img src="https://vibromera.eu/wp-content/uploads/2024/11/2-Camera_01.png" alt="2-Camera_01" style="width: 50%; display: block; margin-bottom: 10px;"> 
> </a> 
> <ul> 
> <li>   Run the rotor up to its operating speed.    </li> 
> <li>   The application will acquire data on vibration magnitude, rotational velocity, and phase angle to determine the initial imbalance state.  </li> 
> </ul> 
>  
> <h3> Attaching the Trial Weight  </h3> 
> <a href="https://vibromera.eu/wp-content/uploads/2024/11/3-Camera-2_01.png" target="_blank"> 
> <img src="https://vibromera.eu/wp-content/uploads/2024/11/3-Camera-2_01.png" alt="3-Camera-2_01" style="width: 50%; display: block; margin-bottom: 10px;"> 
> </a> 
> <ul> 
> <li>  Halt the rotation and mount a test weight at a designated position on the rotor, with the weight's value entered into the software (usually in grams).  </li> 
> <li>   Restart the rotor, and the software will record the changes in vibration level and phase angle.    </li> 
> </ul> 
> <a href="https://vibromera.eu/wp-content/uploads/2024/11/5-Camera_01.png" target="_blank"> 
> <img src="https://vibromera.eu/wp-content/uploads/2024/11/5-Camera_01.png" alt="5-Camera_01" style="width: 50%; display: block; margin-bottom: 10px;"> 
> </a> 
>  
>  
> <h3> Determining the Corrective Mass  </h3> 
> <ul> 
> <li>  The software uses the measured values to automatically compute the necessary compensating weight's magnitude and placement angle.  </li> 
> <li>   The results of the calculation are shown both numerically and visually through charts and graphs.  </li> 
> </ul> 
> <a href="https://vibromera.eu/wp-content/uploads/2024/02/Bs1ManualEngV156-May2023-10448629.png" target="_blank"> 
> <img src="https://vibromera.eu/wp-content/uploads/2024/02/Bs1ManualEngV156-May2023-10448629.png" alt="Bs1 Manual" style="width: 30%; display: block; margin-bottom: 10px;"> 
> </a> 
>  
> <h3> Attaching the Corrective Mass  </h3> 
> <ul> 
> <li>  Attach the computed compensating weight to the rotor as indicated by the software's output.  </li> 
> <li>   If necessary, perform intermediate checks to verify that the imbalance is being reduced.    </li> 
> </ul> 
> <a href="https://vibromera.eu/wp-content/uploads/2024/11/1-Camera-2_01.png" target="_blank"> 
> <img src="https://vibromera.eu/wp-content/uploads/2024/11/1-Camera-2_01.png" alt="1-Camera-2_01" style="width: 50%; display: block; margin-bottom: 10px;"> 
> </a> 
>  
> <h3>  Final Check and Balance Confirmation  </h3> 
> <ul> 
> <li>   Once the corrective weight is in place, restart the rotor and measure the remaining vibration amplitude.  </li> 
> <li>   If the vibration level is within acceptable limits (according to ISO 1940), the balancing is complete.    </li> 
> <li>   Should the vibration still be excessive, repeat the balancing steps, making further adjustments to the corrective weight as needed.  </li> 
> </ul> 
>  
> <h3> Creating a Balancing Report  </h3> 
> <ul> 
> <li>  The program stores the balancing data, allowing you to generate and print a comprehensive report including vibration measurements, corrective weight details, and its angular placement.  </li> 
> </ul> 
>  
> <h3> Final Recommendations  </h3> 
> <ul> 
> <li>  Verify the secure attachment of all balancing weights and measurement sensors.  </li> 
> <li>   Ensure the rotor rotates smoothly and without excessive noise.    </li> 
> <li>   In cases where the rotor is integrated into a more complex system, ensure the correct operation and interaction of all related components.  </li> 
> </ul> 
>  
> <p>  Following this procedure enables accurate balancing, minimizes vibration, and prolongs the service life of the equipment.  </p> 
>  
>  
>  
>  
> Instagram: https://www.instagram.com/vibromera_ou/ 
> Youtube :  https://youtu.be/guA6XJ-ArZM?si=vmkuX7RILzKBl0zL  
> Our website about  <a href="https://vibromera.eu   
> "> Vibrometer </a> 
> Machinio: https://www.machinio.com/listings/98380186-portable-balancer-vibration-analyzer-balanset-1a-full-kit-in-portugal 
> Facebook: https://www.facebook.com/marketplace/item/350151228150722
 > 
 >

웹 에디터 끝

링크 #1

링크 #2

자동등록방지

자동등록방지 숫자를 순서대로 입력하세요.

취소

회원로그인

회원가입

자유게시판 글답변

인기검색어